|
Post by killermidget on Feb 12, 2017 15:45:40 GMT -5
Not all limbs back off equally. Did measure the tiller after letdown?
|
|
|
Post by shredder4286 on Feb 12, 2017 16:01:37 GMT -5
Not yet. I haven't tweaked anything like that on a bow for a while, so I wanted to refresh my memory how to change of it needed.
|
|
|
Post by shredder4286 on Feb 12, 2017 16:02:29 GMT -5
Anybody have a reccomendatiom for a cable slide? I keep reading that they all have problems, and that the stock elite slide wears on the cables
|
|
|
Post by shredder4286 on Feb 12, 2017 16:06:13 GMT -5
Not all limbs back off equally. Did measure the tiller after letdown? No. I'll have to check that
|
|
|
Post by killermidget on Feb 12, 2017 16:09:48 GMT -5
Good luck , I hope it all works out. Those are nice bows...
|
|
|
Post by harley08 on Feb 12, 2017 16:45:12 GMT -5
Anybody have a reccomendatiom for a cable slide? I keep reading that they all have problems, and that the stock elite slide wears on the cables I put a bomar slide on mine. It works well.
|
|
|
Post by harley08 on Feb 12, 2017 16:49:28 GMT -5
There's also a good sticky on tuning a Elite over on AT.
|
|
|
Post by shredder4286 on Feb 12, 2017 17:03:50 GMT -5
There's also a good sticky on tuning a Elite over on AT. I'm In the elite specific forum?
|
|
|
Post by harley08 on Feb 12, 2017 17:04:17 GMT -5
There's also a good sticky on tuning a Elite over on AT. I'm In the elite specific forum? Yep
|
|
|
Post by shredder4286 on Feb 12, 2017 17:04:50 GMT -5
I always miss those stickies. Thanks
|
|
|
Post by elkguide on Feb 12, 2017 17:46:44 GMT -5
I did. Not as bad but still there. Maybe I just didn't notice before? Definitely check timing. Vibrations are not something that is common with Elites.
|
|
|
Post by shredder4286 on Feb 12, 2017 18:05:30 GMT -5
The limb stop on the top cam is hitting ahead by about 1/16" (a Little less). I can just move the bottom limb stop so they both hit at the same time correct?
|
|
|
Post by killermidget on Feb 12, 2017 18:15:09 GMT -5
The limb stop on the top cam is hitting ahead by about 1/16" (a Little less). I can just move the bottom limb stop so they both hit at the same time correct? Either way, just moving 1/16 won't matter much.
|
|
|
Post by elkguide on Feb 12, 2017 19:05:16 GMT -5
The limb stop on the top cam is hitting ahead by about 1/16" (a Little less). I can just move the bottom limb stop so they both hit at the same time correct? Depending on a bunch of things. Maybe you need to move the top stop to time it correctly but either way, they should both be hitting at the same time.
|
|
|
Post by stixshooter on Feb 12, 2017 19:45:56 GMT -5
I picked up a Bear Empire single cam, I think it's a 2014 for dirt cheap. I'm really surprised how nice it shoots. I really haven't paid any attention to Bear over the last 35 years but I like it
|
|
|
Post by shredder4286 on Feb 12, 2017 20:08:20 GMT -5
There's also a good sticky on tuning a Elite over on AT. So when you're checking timing by the dots- He said "inner cable"- That's be the one closest to the riser? By those cables and dogs my timing is perfect
|
|
|
Post by harley08 on Feb 12, 2017 20:18:38 GMT -5
There's also a good sticky on tuning a Elite over on AT. So when you're checking timing by the dots- He said "inner cable"- That's be the one closest to the riser? By those cables and dogs my timing is perfect Correct
|
|
|
Post by shredder4286 on Feb 12, 2017 20:49:30 GMT -5
Not all limbs back off equally. Did measure the tiller after letdown? Tiller is same top and bottom. Inner cable towards riser crosses same dot at the exact same place. I just ran some heavier arrows in a 340 spine through it for fun and it was quieter with minimal vibrations- no hand shock. I did move the limb stop in a bit also, but didn't twist any cables.
|
|
|
Post by kicker338 on Feb 13, 2017 20:48:29 GMT -5
For a better cable slide you might try the new pse roller slide. Several guys on AT have switched to them on their elites said it was the best thing they ever did. The price has dropped from $50 to $35 for them too.
|
|
|
Post by harley08 on Feb 13, 2017 23:20:02 GMT -5
For a better cable slide you might try the new pse roller slide. Several guys on AT have switched to them on their elites said it was the best thing they ever did. The price has dropped from $50 to $35 for them too. I was going to recommend the PSE roller slide, but not having tried one myself, felt it was best to say what I use. May pick one up sometime.
|
|